A chair can fit an older adult’s body and still be difficult to get out of. A 3D scan can help a designer assess seat width and depth. Watching the same person stand up reveals a different set of design questions about seat height, armrest placement and the effort the task requires.
Sarcopenia, the progressive loss of skeletal muscle strength and mass with age, is one reason the two can differ. It occurs alongside other age-related changes, such as fat redistribution, postural change and stature loss, that also affect how products fit. Knowing what 3D body shape can and cannot show helps designers of healthcare products, furniture, mobility aids and consumer goods decide what to measure, and what to test with real users.
What Sarcopenia Is
Sarcopenia is recognized as a muscle disease associated with aging. Under the European EWGSOP2 criteria, low muscle strength indicates probable sarcopenia, low muscle quantity or quality confirms it, and low physical performance indicates severe sarcopenia. The Asian Working Group for Sarcopenia (AWGS) 2025 consensus update instead requires both low muscle mass and low muscle strength, and treats physical performance as an outcome measure.
Clinically, sarcopenia is associated with falls, fractures, loss of independence and higher healthcare costs. For designers, its significance is more practical: it changes both what the body can do and what the body looks like.
How Aging Changes Body Shape
Several changes tend to occur together in later life, though their extent varies widely between individuals. Not all of them are caused by sarcopenia, but each can affect product fit:
| Change | What happens | Possible implications for fit |
|---|---|---|
| Muscle loss | Reduced muscle volume, particularly in the lower limbs | Thinner thighs and calves, reduced buttock volume |
| Fat redistribution | Fat shifts toward the trunk and abdomen, and into muscle tissue | Larger waist and abdominal depth even when body weight is stable |
| Postural change | Increased thoracic curvature and forward head posture | Rounded upper back, lower eye height, altered shoulder position |
| Stature loss | Compression of intervertebral discs and vertebral changes | Reduced sitting height and standing height |
| Joint changes | Reduced range of motion in shoulders, hips, spine and ankles | Limited reach and more difficulty rising from seated positions |
A particular challenge is sarcopenic obesity. Sarcopenic obesity involves excess body fat together with low muscle mass and impaired muscle function. For a product designer, body weight alone gives little guidance on thigh shape, seat width or the effort required to stand.
Why One-Dimensional Measurements Miss the Picture
Traditional anthropometric tables report circumferences, lengths and breadths. They capture some of these changes, such as waist circumference and stature. But they struggle to represent how shape changes as a whole: a thinner limb combined with a fuller trunk, a rounded back combined with a forward head position.
Calf circumference, for example, is used in some sarcopenia screening approaches as a screening measure that helps identify people who may need further assessment. It is a single line on a three-dimensional body. 3D body scanning captures the full surface and shows how volume and contour differ across the body. Strength has to be measured separately, and how people move has to be observed in use.

Design Implications Across Product Categories
When body shape is understood as part of aging, design priorities become clearer:
- Seating and furniture. Reduced lower limb strength makes rising from a chair harder, and in a study of chair design, lower seats made rising slower and more difficult for older adults. Seat height should support sit-to-stand movement; cushion firmness and armrest placement are design variables to confirm with users. Use the seated body model to review cushion width and depth. Check pressure distribution with a pressure mat, then observe how the user rises from the chair at different seat heights.

- Wearable and supportive devices. Match each product to the body region it contacts. For a knee brace, compare thigh and calf contours where the straps fasten. For a torso-worn sensor, check how the housing sits against the body in both seated and standing postures.
- Mobility aids. Walkers, canes and rollators should match changes in posture, including forward lean and reduced shoulder mobility.
- Apparel and closures. Changes in trunk shape alter garment fit, while reduced grip strength makes small buttons and stiff closures harder to manage.
- Everyday products. Handles, lids, packaging and controls should require less grip force and allow use with weaker hands.
Using 3D Body Data for Older Populations
Before using an anthropometric dataset, check whether it covers the ages and functional levels of the intended users. Some datasets group all older adults into a single age band, despite large differences between a healthy 65-year-old and a frail 85-year-old. Used carefully, 3D body data offers a more useful foundation:
- Characterize the population. Use 3D body data from older adults to describe body shape across age, sex and functional status.
- Identify shape patterns. Group scans by features relevant to the product, such as thigh circumference, abdominal depth or upper-back curvature. Where strength or body-composition measurements are available, link them to the corresponding scans. Lee and You used 3D head scans to generate representative models that capture variation in head shape. For a brace or a seat, the same design question starts with scans of the body region that comes into contact with the product.
- Evaluate fit and function. Test products on representative 3D models for fit, contact and clearance, and combine shape data with mobility and strength data to assess usability.
- Track change over time. Where longitudinal data is available, understand how shape changes as people age, so products can accommodate users throughout their later years.

Comfo Labs works with healthcare and consumer product teams to apply 3D human body data and digital human evaluation to older populations, helping teams design for the bodies older adults actually have. SIZE LAB provides 3D body-shape data, anthropometric measurements, and representative 3D personas for older body types, and doodll.ai supports concept exploration, design variations, and 3D visualization of age-friendly product options.
Function and Shape Must Be Considered Together
Body shape data is most useful when it is linked to function. A thinner thigh is a fit issue for a brace or garment, but it does not tell the designer how much leg strength a person has; muscle mass and strength do not necessarily decline at the same rate, so strength needs to be measured separately. A fuller trunk changes not only clothing fit but also how a person bends forward to reach the floor.
This is why the most effective designs for older adults combine three types of information:
- Shape: 3D body data describing limb and trunk geometry, posture and stature.
- Capacity: Measure strength separately, for example with a grip-strength test. Use the five-times chair stand to assess standardized task performance, then observe how users rise from the actual chair, with armrests available if the product provides them.
- Mobility: joint range of motion and movement data showing how older adults reach, bend, rise and walk.

Products evaluated against all three are more likely to suit older adults in daily life. A chair that fits the body but demands more leg strength than a user has to rise from it has not solved the real problem.
Designing for Aging Bodies: Review Checklist
- Representative data: Does the design data include older adults across a range of ages and functional levels?
- Shape types: Has the design been checked across a range of trunk and limb shapes, not a single elderly average?
- Posture: Does the design account for forward head posture and increased thoracic curvature?
- Strength: Are grip, push and sit-to-stand demands within the capacity of weaker users?
- Contact and pressure: Have pressure points been checked for users with reduced soft tissue?
- Sizing: Do sizing systems reflect older body proportions rather than adapted younger ones?
A seated scan helps a designer choose a cushion width and depth. A trial with the chair shows where the user places their feet, when they reach for the armrests and how they rise. Together, those observations guide the next design revision.
Frequently Asked Questions
Can a 3D body scan diagnose sarcopenia?
No. A 3D surface scan shows external body shape in the posture captured. It does not directly measure muscle strength or composition. For product design, use it to check fit and clearance, then use separate strength and movement assessments to understand how people will use the product.
What is sarcopenia?
Sarcopenia is a muscle disease that affects strength and physical function. Under European criteria, low strength indicates probable sarcopenia, and low muscle quantity or quality confirms the diagnosis. The 2025 Asian consensus requires both low muscle strength and low muscle mass.
How does sarcopenia change body shape?
Sarcopenia mainly reduces muscle mass and strength, which can show as reduced volume in the thighs, calves and buttocks. Other age-related changes, such as fat shifting toward the trunk, a more rounded upper back and loss of stature, often occur at the same time but are not caused by sarcopenia alone. Together they can change how products fit.
What is sarcopenic obesity?
Sarcopenic obesity involves excess body fat together with low muscle mass and impaired muscle function. Body weight or BMI alone cannot identify it; diagnosis requires assessing both muscle function and body composition.
At what age does muscle loss begin?
Muscle mass and strength generally begin a gradual decline in middle adulthood, and the decline tends to accelerate in later life. The rate varies widely with activity, nutrition and health, which is why older adults often differ more from one another than younger adults do.
How should products be designed for older adults with sarcopenia?
Seats should support easy sit-to-stand movement and spread pressure on reduced soft tissue, braces and garments should fit a range of limb and trunk shapes, and handles, lids and closures should need less grip force. Designs should be tested on several older body types, not one elderly average.
How can I tell whether a body-scan dataset represents my older users?
Check how many scans fall in each age band you are designing for, including the oldest users, and whether the dataset includes the postures and functional measurements your product needs, such as seated scans or grip strength. If they are missing, plan additional measurement or user testing.
WORK WITH COMFO LABS
Designing a product for older adults?
Tell us who will use it and what they need to do. We can help you review product fit, contact areas and the movements involved.
References
- Alexander, N. B., Koester, D. J., & Grunawalt, J. A. (1996). Chair design affects how older adults rise from a chair. Journal of the American Geriatrics Society, 44(4), 356–362. https://doi.org/10.1111/j.1532-5415.1996.tb06402.x
- Chen, L. K., Woo, J., Assantachai, P., Auyeung, T. W., Chou, M. Y., Iijima, K., et al. (2020). Asian Working Group for Sarcopenia: 2019 consensus update on sarcopenia diagnosis and treatment. Journal of the American Medical Directors Association, 21(3), 300–307.e2. https://pubmed.ncbi.nlm.nih.gov/32033882/
- Chen, L. K., Hsiao, F. Y., Akishita, M., Assantachai, P., Lee, W. J., Lim, W. S., et al. (2025). A focus shift from sarcopenia to muscle health in the Asian Working Group for Sarcopenia 2025 consensus update. Nature Aging, 5(11), 2164–2175. https://doi.org/10.1038/s43587-025-01004-y
- Cruz-Jentoft, A. J., Bahat, G., Bauer, J., Boirie, Y., Bruyère, O., Cederholm, T., et al. (2019). Sarcopenia: Revised European consensus on definition and diagnosis. Age and Ageing, 48(1), 16–31. https://pmc.ncbi.nlm.nih.gov/articles/PMC6322506/
- Donini, L. M., Busetto, L., Bischoff, S. C., Cederholm, T., Ballesteros-Pomar, M. D., Batsis, J. A., et al. (2022). Definition and diagnostic criteria for sarcopenic obesity: ESPEN and EASO consensus statement. Obesity Facts, 15(3), 321–335. https://doi.org/10.1159/000521241
- Lee, W., & You, H. (2022). A method for the generation of shape-based percentile representative human models for ergonomic product design. Journal of the Ergonomics Society of Korea, 41(6), 547–559. https://doi.org/10.5143/JESK.2022.41.6.547
